新聞中心
NEWS CENTER
聯系我們
CONTACTS US
濟南皓暉建材有限公司，總部位于中國泉城——山東濟南，是一家專業生產銷售石塑電梯門套，仿大理石電梯門套的專業廠家。皓暉建材在電梯門套生產行業很多年，憑著優質的產品質量和完善的售后服務，在全國各地都有我們的工程案例。
我們本著“以質量求生存 ，靠管理出效益，憑信譽贏口碑,以實干筑輝煌”的經營理念，公司將立足于當代建材現代化發展前沿，依靠科技、勇于探索，以優質產品優良服務、信譽與廣大用戶攜手共創輝煌。
聯系電話： 15853163650
工廠地址：山東濟南章丘區（歡迎廣大客戶來廠勘察）
行業新聞
COMPANY NEWS
仿大理石uv裝飾板的安裝方法介紹
2016-04-11 09:50:19 文章來源：m.xraqjs.com
一. 鋁合金固定
Aluminum alloy fixed
1、先要在墻面上覆上一面基層，常用的是3MM的三合板，木工板，好點是防火玻鎂板，用氣釘把它們釘在墻面上。
1, first in the wall to cover a basic level, is commonly used in 3MM three plywood, wood board, good point is fire glass magnesium board, with gas nails they nailed on the wall.
2、再在墻面上釘腳線。用鋁合金陰角固定墻角、再用鋁合金工具條固定墻角。也就是分別把鋁合金陰角和鋁合金工具條分別用釘子釘在墻面的相應位置。
3, and then saw UV board. The UV board according to the actual requirements of the size of sawing a piece, then sawing with sandpaper smooth and clean dressing.
4、再將UV板嵌入鋁合金陰角和工具條之間就行了。
4, and then UV plate embedded in the negative angle and the tool bar between the.
二. 用墻面膠安裝
Two. Install with wall plastic
1、先要在墻面上覆上一面基層，常用的是3MM的三合板，木工板，好點是防火玻鎂板。用氣釘把它們釘在墻面上，并用沙紙將板面清潔干凈。
1, the first to be covered on the wall of the grass, the commonly used 3MM three plywood, wood panels, good point is the fire glass magnesium board. Gas nail nail them on the wall, and the clean surface with sandpaper.
2、鋸板，將UV板安實際要求鋸成一塊塊的。
2, saw plate, UV plate of an actual requirement of sawn pieces.
3、倒邊，將要安裝的UV板四邊用倒邊機倒成45度角。根據實際安裝要求，有的只需倒上下兩邊或是三個邊。
3, the reverse side, will be installed on the side of the UV board with the inverted edge machine down to 45 degrees. According to the actual installation requirements, and some only need to fall on either side or three sides.
4、清潔UV板背面，用沙紙和抹布將UV板背面清潔干凈。
4, clean the UV plate with sandpaper and back cloth to clean the board back UV.
5、將萬能膠或木工膠均勻涂在UV板背面，然后將UV板平整地貼在墻面上，再用手輕輕捶打UV板，讓UV板好好牢固粘在墻面上。
5, will be in carpentry or all-purpose adhesive glue evenly painted UV board back, then UV plate is flat and affixed to the wall, and then gently beat UV board, UV board to take firmly glued to the wall.
6、調水性填縫料，然后將填縫料填在兩張UV板45度角相交處，先填滿，再用木板垂直角從45度角相交處輕輕劃過，這樣45度相交處就好看了。
6, water gap filling material, then filling material filled in the two UV board at a 45 degree angle intersection to fill, reoccupy board vertical angle from the 45 degree angle intersect at gently across, such 45 degrees at the intersection of the good.
7、清潔UV板表面，將多余的填縫料清潔干凈。
7, clean the surface of the UV board, the excess sealant clean.
本文來自：仿大理石線條更多的精彩內容請點擊我們的官方網站：http://m.xraqjs.com
This article from: imitation marble lines more exciting content please click on our official website: http://m.xraqjs.com
Aluminum alloy fixed
1、先要在墻面上覆上一面基層，常用的是3MM的三合板，木工板，好點是防火玻鎂板，用氣釘把它們釘在墻面上。
1, first in the wall to cover a basic level, is commonly used in 3MM three plywood, wood board, good point is fire glass magnesium board, with gas nails they nailed on the wall.
2、再在墻面上釘腳線。用鋁合金陰角固定墻角、再用鋁合金工具條固定墻角。也就是分別把鋁合金陰角和鋁合金工具條分別用釘子釘在墻面的相應位置。
2, and then nail the foot line on the wall. With aluminum alloy corner fixed corner, and then fixed corner of aluminum alloy tools. That is, respectively, the aluminum alloy and aluminum alloy tool bar with a nail in the wall of the corresponding position.
3, and then saw UV board. The UV board according to the actual requirements of the size of sawing a piece, then sawing with sandpaper smooth and clean dressing.
4、再將UV板嵌入鋁合金陰角和工具條之間就行了。
4, and then UV plate embedded in the negative angle and the tool bar between the.
二. 用墻面膠安裝
Two. Install with wall plastic
1、先要在墻面上覆上一面基層，常用的是3MM的三合板，木工板，好點是防火玻鎂板。用氣釘把它們釘在墻面上，并用沙紙將板面清潔干凈。
1, the first to be covered on the wall of the grass, the commonly used 3MM three plywood, wood panels, good point is the fire glass magnesium board. Gas nail nail them on the wall, and the clean surface with sandpaper.
2、鋸板，將UV板安實際要求鋸成一塊塊的。
2, saw plate, UV plate of an actual requirement of sawn pieces.
3、倒邊，將要安裝的UV板四邊用倒邊機倒成45度角。根據實際安裝要求，有的只需倒上下兩邊或是三個邊。
3, the reverse side, will be installed on the side of the UV board with the inverted edge machine down to 45 degrees. According to the actual installation requirements, and some only need to fall on either side or three sides.
4、清潔UV板背面，用沙紙和抹布將UV板背面清潔干凈。
4, clean the UV plate with sandpaper and back cloth to clean the board back UV.
5、將萬能膠或木工膠均勻涂在UV板背面，然后將UV板平整地貼在墻面上，再用手輕輕捶打UV板，讓UV板好好牢固粘在墻面上。
5, will be in carpentry or all-purpose adhesive glue evenly painted UV board back, then UV plate is flat and affixed to the wall, and then gently beat UV board, UV board to take firmly glued to the wall.
6、調水性填縫料，然后將填縫料填在兩張UV板45度角相交處，先填滿，再用木板垂直角從45度角相交處輕輕劃過，這樣45度相交處就好看了。
6, water gap filling material, then filling material filled in the two UV board at a 45 degree angle intersection to fill, reoccupy board vertical angle from the 45 degree angle intersect at gently across, such 45 degrees at the intersection of the good.
7、清潔UV板表面，將多余的填縫料清潔干凈。
7, clean the surface of the UV board, the excess sealant clean.
本文來自：仿大理石線條更多的精彩內容請點擊我們的官方網站：http://m.xraqjs.com
This article from: imitation marble lines more exciting content please click on our official website: http://m.xraqjs.com
